Datacom Systems D56 Guía para resolver problemas descargar pdf (Pagina 63)

–63–

10 INPUT DEV: LP#

RF TRANS. RF: 1

Loop number (LP#): Enter the loop number (1-4) for the zone of the

transmitter being enrolled. The default is loop "1." To accept this,

press [

✱

]. If a different loop number is being used on this transmit-

ter, enter the desired loop number and press [

✱

] to continue (see the

transmitter's Installation Instructions for specific loop designations).

The loop number must be entered here, whether using Zone

Programming or Sequential Mode to "enroll" transmitters.

10 LEARN S/N?

0 = NO, 1 = YES 0

If the transmitter’s serial number has not been previously “enrolled,”

you may enter the enroll mode now by either entering "1" (YES) or by

pressing the upper left-hand button of the program tool. If using the

program tool, move to the physical location of the transmitter

to be enrolled before pressing the button. A single short beep

will verify that the button has been pressed. The system will respond

to the first serial number transmitted after the [

✱

] key on the keypad

or the button of the program tool is pressed. Enter "0" (NO) if you

wish to enroll the transmitter later, using the “✱83 sequential” mode

described in the SEQUENTIAL MODE section later in this manual.

If "0" is entered, skip to the summary screen prompt.

10 INPUT S/N: L

A X X X–X X X X

This prompt is displayed if "1" (YES) is entered in response to the

"Learn S/N?" prompt. The serial number may be enrolled by one of

two methods:

a) Enter the 7-digit serial number printed on the transmitter using

an alpha keypad

b) Activate the transmitter by faulting or restoring the input you

wish to use for that zone (e.g., press a button, open or close a door,

etc.).

10 INPUT S/N: L

A002-4064 1

The system will enroll the serial number of the first transmitter

heard, add the loop number entered to this serial number, display the

serial and loop numbers, and cause the keypad to beep twice.

If the serial and loop number combination is already present in the system, a

single long beep will be heard from the keypad. If this happens, the system will

not display the serial number, but will wait for a transmission from another

transmitter or transmitter loop input.

The system will then enter an optional confirmation mode so that the

operation of the actual programmed input can be confirmed. Activate

the loop input or button that corresponds to this zone. We

recommend that you confirm the programming of every

transmitter before proceeding to the next zone.

10 CONFIRMED

A022-4064 1

When the system sees activity on the appropriate input, it will beep

three times and display the confirmation message.

At any time during this step, you may press the [

✱

] key on the keypad or the

upper left-hand button of the program tool if you are satisfied with the serial and

loop number combination that has been enrolled, regardless of whether or not

the enrolled input has been "confirmed."

If the incorrect transmitter has been enrolled, press the [#] key on the keypad or

the upper right-hand button of the program tool to delete the serial number and

return to the "LEARN S/N" prompt. A single long beep will be heard from the

keypad to verify pressing of the upper right-hand button. Then, press "1" (YES)

or press the upper left-hand button of the program tool (a single short beep will

verify the system is ready for enrolling) and re-activate the proper transmitter or

transmitter loop input.

1 2 ... 58 59 60 61 62 63 64 65 66 67 68 ... 103 104

Comentarios a estos manuales

Sin comentarios

Datacom Systems D56 Guía para resolver problemas Pagina 63

Comentarios a estos manuales

Relacionado con productos y manuales para Redes Datacom Systems D56